おまえの hddparm -tT 教えてください。

bash# cat /proc/ide/hda/model
TOSHIBA MK6015MAP
/dev/hda:
Timing buffer-cache reads: 64 MB in 0.55 seconds =116.36 MB/sec
Timing buffered disk reads: 32 MB in 2.44 seconds =13.11 MB/sec

bash-2.05# cat /proc/ide/hda/model
FUJITSU MPG3409AT E
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.04 seconds =123.08 MB/sec
Timing buffered disk reads: 64 MB in 2.35 seconds = 27.23 MB/sec

bash-2.05# cat /proc/ide/hdc/model
IBM-DPTA-372050
/dev/hdc:
Timing buffer-cache reads: 128 MB in 1.01 seconds =126.73 MB/sec
Timing buffered disk reads: 64 MB in 2.94 seconds = 21.77 MB/sec

cat /proc/ide/hda/media
disk

$ hddparm -tT
bash: hddparm: command not found

>>3 俺に対する朝鮮^H^H挑戦か？

$cat /proc/ide/hda/model
Maxtor 91020U3

# /sbin/hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.88 seconds =145.45 MB/sec
Timing buffered disk reads: 64 MB in 3.52 seconds = 18.18 MB/sec

Vendor: IBM-PSG Model: DDYS-T09170M M Rev: S9HA

/dev/sda:
Timing buffer-cache reads: 128 MB in 1.23 seconds =104.07 MB/sec
Timing buffered disk reads: 64 MB in 2.01 seconds = 31.84 MB/sec

Vendor: FUJITSU Model: MAJ3364MC Rev: 3702

/dev/sdb:
Timing buffer-cache reads: 128 MB in 1.19 seconds =107.56 MB/sec
Timing buffered disk reads: 64 MB in 1.92 seconds = 33.33 MB/sec

SCSI
Chip NCR53C895, device id 0xc, revision id 0x2
On PCI bus 0, device 13, function 0, IRQ 10
Synchronous period factor 10, max commands per lun 32

Vendor: IBM Model: DNES-318350W Rev: SA30

/dev/sda:
Timing buffer-cache reads: 128 MB in 0.88 seconds =145.45 MB/sec
Timing buffered disk reads: 64 MB in 3.32 seconds = 19.28 MB/sec

mona@2ch:~$ cat /proc/ide/hda/model
TOSHIBA MK2016GAP

mona@2ch:~$ sudo /sbin/hdparm -tT /dev/hda
Password:

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.04 seconds =123.08 MB/sec
Timing buffered disk reads: 64 MB in 15.71 seconds = 4.07 MB/sec

[root@hoge 1002]# /sbin/hdparm -tT /dev/hdc

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.89 seconds = 33.86 MB/sec
[root@hoge 1002]# cat /proc/ide/hdc/model
IC35L060AVER07-0

速いのでまんぞくしてます。(クラッシュ時のデータ損失が恐い)

#hdparm -itT /dev/hda

/dev/hda:

Model=IBM-DTLA-307020, FwRev=TX3OA50C, SerialNo=YHDYHT8T768
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
Timing buffer-cache reads: 128 MB in 1.77 seconds = 72.32 MB/sec
Timing buffered disk reads: 64 MB in 2.60 seconds = 24.62 MB/sec

英語のman 読むのもたるいので，
なにするコマンドか，-tT オプションを含めて
説明希望

>>11
俺のにはmanもなかった
No manual entry for hddparm

>9
速いですね。 IDE で 30MB/sec. 越えてるの、はじめて見ました。

>12
いぢめんといて(w
ネタだと思うけど念のため。 man hdparm っす。

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 19.87 seconds = 3.22 MB/sec
[root@fireball]:~-> hdparm -tT /dev/hdb

/dev/hdb:
Timing buffer-cache reads: 128 MB in 1.18 seconds =108.47 MB/sec
Timing buffered disk reads: 64 MB in 6.03 seconds = 10.61 MB/sec

速いのか遅いのかようわからんす

まあ、平均的なところか。

/dev/hda:

Model=FUJITSU MPG3307AT, FwRev=02B9, SerialNo=VG13P1201DB7
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60046560
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Timing buffer-cache reads: 128 MB in 0.67 seconds =191.04 MB/sec
Timing buffered disk reads: 64 MB in 2.76 seconds = 23.19 MB/sec

disk readが11.96MB/秒か。おそい。

SeagateのST380021Aの購入を検討してるんですが、
誰か使ってる人います?

# cat /proc/ide/hda/model
IBM-DTTA-351010
# hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1232/255/63, sectors = 19807200, start = 0
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 2.69 seconds = 47.58 MB/sec
Timing buffered disk reads: 64 MB in 5.35 seconds = 11.96 MB/sec

>>10 との違いは udma5 か？

/dev/hda:

Model=IBM-DTLA-307045, FwRev=TX6OA50C, SerialNo=YMDYMT8V657
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=90069840
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.23 seconds =104.07 MB/sec
Timing buffered disk reads: 64 MB in 1.95 seconds = 32.82 MB/sec

LANより遅いぞっ

Model=IBM-DPTA-351500, FwRev=P54OA30A, SerialNo=JGYJGT0V480
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=425kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=29336832
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
Kernel Drive Geometry LogicalCHS=1826/255/63 PhysicalCHS=29104/16/63
Timing buffer-cache reads: 128 MB in 10.60 seconds = 12.08 MB/sec
Timing buffered disk reads: 64 MB in 11.88 seconds = 5.39 MB/sec

も一つ。「Timing buffer-cache reads」がどうにも。

Model=FUJITSU MPE3273AH, FwRev=EH-A2-27, SerialNo=01005815
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=53359376
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Drive Supports : ATA-1 ATA-2 ATA-3 ATA-4
Kernel Drive Geometry LogicalCHS=3321/255/63 PhysicalCHS=52935/16/63
Timing buffer-cache reads: 128 MB in 2.23 seconds = 57.40 MB/sec
Timing buffered disk reads: 64 MB in 2.96 seconds = 21.62 MB/sec

>18
うは、 udma4 で 5.39 MB/sec. って一体(笑)

>9
今気付いたけど Timing buffer-cache reads が 556.52 MB/sec. って
凄まじい…

$ sudo hdparm -iTt /dev/hda

/dev/hda:

Model=IBM-DTLA-307030, FwRev=TX4OA50C, SerialNo=YK0YKT7Q703
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=60036480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Timing buffer-cache reads: 128 MB in 0.98 seconds =130.61 MB/sec
Timing buffered disk reads: 64 MB in 2.46 seconds = 26.02 MB/sec

BXﾏﾏﾝなんで、ATA33なのだが、悪い結果ではないのかな。
ATA66/100 を Linuxで使うときに ATA33より体感速度は向上する？

-T
Perform timings of cache reads for benchmark and comparison
purposes. For meaningful results, this operation should be repeated
2-3 times on an otherwise inactive system (no other active processes)
with at least a couple of megabytes of free memory. This displays the
speed of reading directly from the Linux buffer cache without disk
access. This measurement is essentially an indication of the
throughput of the processor, cache, and memory of the system under
test. If the -t flag is also specified, then a correction factor based
on the outcome of -T will be incorporated into the result reported for
the -t operation.

-t
Perform timings of device reads for benchmark and comparison purposes.
For meaningful results, this operation should be repeated 2-3 times on
an otherwise inactive system (no other active processes) with at least
a couple of megabytes of free memory. This displays the speed of
reading through the buffer cache to the disk without any prior caching
of data. This measurement is an indication of how fast the drive can
sustain sequential data reads under Linux, without any filesystem
overhead. To ensure accurate measurments, the buffer cache is flushed
during the processing of -t using the BLKFLSBUF ioctl. If the -T flag
is also specified, then a correction factor based on the outcome of -T
will be incorporated into the result reported for the -t operation.

>>20
i850/P4/2GHz/ECC RIMMです。バーストは大したことないけど
もしかすると連続したデータ移動にはi850は強いかも

>23
なるほど。どーりで…
さすが世代が違うって感じですねぇ。

# はぁ、ウチもそろそろ速い機械にしたい…

僅差だけどちと速い(@2.4.13-pre2)

[root@hogehoge]# /sbin/hdparm -tT /dev/hdc

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.22 seconds =581.82 MB/sec
Timing buffered disk reads: 64 MB in 1.86 seconds = 34.41 MB/sec
[root@hogehoge]# cat /proc/ide/hdc/model
IC35L060AVER07-0

スレタイトル間違ってるけど、興味深いので age.

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.24 seconds =103.23 MB/sec
Timing buffered disk reads: 64 MB in 20.49 seconds = 3.12 MB/sec

これ，もしかして，すごい遅いんですか？

/dev/hda:
Timing buffer-cache reads: 64 MB in 1.62 seconds =39.51 MB/sec
Timing buffered disk reads: 32 MB in 7.26 seconds = 4.41 MB/sec
bash# cat /proc/ide/hda/model
WDC WD136AA

鬱田市納。
DMA 入れると固まるし。

うは、上がってるし。(w

最近組み立てた AthlonXP 1600+(FSB140 駆動) / PC2100 Registered では、
確か cache read が 200MB/sec. ちょいくらいだったかな。

今は Windows しか入ってないんで、詳細なデータ出せなくてスマヌ。。。

1号機
----------
QUANTUM　FIREBALL_TM3200A

Timing buffer-cashe reads: 128MB in 3.96 seconds = 32.32MB/sec
Timing buffered disk reads: 64MB in 9.47 seconds = 6.76MB/sec

-------
FMV-5200T5 with P200

hdparm is a Linux utility for viewing/manipulating various
IDE drive and driver parameters. Most systems can benefit
from improved performance using a command sequence similar to this:

#!/bin/sh
for d in /proc/ide/hd* ; do
if [ `cat $d/media` = 'disk' ]; then
hdparm -qm8 -qu1 -qc1 -qd1 -qW1 /dev/${d##*/}
elif [ `cat $d/media` = 'cdrom' ]; then
hdparm -qu1 -qd1 /dev/${d##*/}
fi
done

# cat /proc/ide/hda/model
WDC WD181AW

# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.95 seconds =134.74 MB/sec
Timing buffered disk reads: 64 MB in 3.24 seconds = 19.75 MB/sec

IBM-DJSA-220
Timing buffer-cache reads: 128 MB in 0.99 seconds =129.29 MB/sec
Timing buffered disk reads:64 MB in 3.99 seconds = 16.04 MB/sec

/proc/sys/vm/max-readahead = 127
/proc/sys/vm/bdflush = "80 0 0 0 6000 18000 90 0 0"

MAXTOR 4K080H4
/dev/hda:
Timing buffer-cache reads: 128 MB in 2.03 seconds = 63.05 MB/sec
Timing buffered disk reads: 64 MB in 5.24 seconds = 12.21 MB/sec
IBM-DTTA-351680
/dev/hdd:
Timing buffer-cache reads: 128 MB in 1.99 seconds = 64.32 MB/sec
Timing buffered disk reads: 64 MB in 5.39 seconds = 11.87 MB/sec

Filesystem Size Used Avail Use% Mounted on
/dev/hda5 73G 54G 15G 78% /
/dev/hda1 97M 12M 80M 13% /boot
/dev/hdd1 7.9G 7.1G 802M 91% /Win1
/dev/hdd5 7.9G 7.7G 238M 98% /Win2

IBM-DTTA-371440

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 5.14 seconds = 12.45 MB/sec

/dev/hda:

Model=WDC WD1000BB-32CCB0, FwRev=22.04A22, SerialNo=WD-WMA9P1098928
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=195371568
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.74 seconds =172.97 MB/sec
Timing buffered disk reads: 64 MB in 1.69 seconds = 37.87 MB/sec

# cat /proc/ide/hda/model
WDC WD400BB-00AUA1
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.17 seconds =109.40 MB/sec
Timing buffered disk reads: 64 MB in 3.39 seconds = 18.88 MB/sec

どうやってチューンナップするかな

# hdparm -itT /dev/hda

/dev/hda:

Model=DupliDisk IDE RAID-1 Adapter( 1.25), FwRev=TAH71DP0, SerialNo=
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=16
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=20010816
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4

Timing buffer-cache reads: 128 MB in 0.97 seconds =131.96 MB/sec
Timing buffered disk reads: 64 MB in 3.63 seconds = 17.63 MB/sec

ソフトウェアRAIDでミラーしてたときはもっと速かったんだが。

cat /proc/ide/hda/model
MAXTOR 4K060H3
hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.67 seconds =191.04 MB/sec
Timing buffered disk reads: 64 MB in 1.98 seconds = 32.32 MB/sec

cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03

hdparm -tT /dev/sda
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.52 seconds =246.15 MB/sec
Timing buffered disk reads: 64 MB in 1.25 seconds = 51.20 MB/sec

/sbin/hdparm -tT /dev/md1

/dev/md1:
Timing buffer-cache reads: 128 MB in 0.47 seconds =272.34 MB/sec
Timing buffered disk reads: 64 MB in 0.60 seconds =106.67 MB/sec

７台の RAID5

うわ、すげぇ。さすが RAID 。 disk reads で 100MB/sec. 越えてるし。

む、 40 さんは一発で 50MB/sec. 越えてる。。。

/sbin/hdparm -itT /dev/hdb

/dev/hdb:

Model=ST360021A, FwRev=3.05, SerialNo=3HR04XL1
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=117231408
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.28 seconds =100.00 MB/sec
Timing buffered disk reads: 64 MB in 4.23 seconds = 15.13 MB/sec

udma2の制限か? そういや、このモードの最大転送速度って、いくつだっけ。

cat /proc/ide/hda/model
ST340823A

hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.70 seconds =182.86 MB/sec
Timing buffered disk reads: 64 MB in 4.28 seconds = 14.95 MB/sec

おせぇ。

hdparm /dev/hda

/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1868/255/63, sectors = 30015216, start = 0

cat /proc/ide/hda/model
Maxtor 91531U3

/sbin/hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.91 seconds =140.66 MB/sec
Timing buffered disk reads: 64 MB in 2.59 seconds = 24.71 MB/sec

ん〜〜ふつうだな・・・

MAXTOR 4K040K2

hdparm -tT /dev/hde
/dev/hde:
Timing buffer-cache reads: 128 MB in 1.06 seconds =120.75 MB/sec
Timing buffered disk reads: 64 MB in 2.00 seconds = 32.00 MB/sec

ST360020A
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.46 seconds =278.26 MB/sec
Timing buffered disk reads: 64 MB in 2.72 seconds = 23.53 MB/sec

イマイチやな。P4X266の板。

IC35L060AVER07-0

/dev/hda:

Model=IC35L060AVER07-0, FwRev=ER6OA44A, SerialNo=SZNSZ0P0424
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.28 seconds =457.14 MB/sec
Timing buffered disk reads: 64 MB in 1.78 seconds = 35.96 MB/sec

IC35L060AVER07-0
結構人気？
シリアルコードの見方がわからないので、
60Gの7500rpm？
\16Kで買いましたけど、安い方かな？

>>49
漏れもIC35L060AVER07-0。16Kくらいだった。
buffered disk readsが38MB/sec〜♪
でもbuffer-cache readsは100MB/sec…。

関係ないけどMozillaで書いてたら逝った…

>>42
>む、 40 さんは一発で 50MB/sec. 越えてる。。。

ASC39160/64bitPCI + Atlas10KIII/18GBです。
10000rpmsだけど今まで使ってたIBM DNES309170より
遥かに静か、かつ無茶苦茶速いです。(シーク音は箱に入った
砂をざーっと何かに出すような音ですが、慣れればIBMより
静かです)

>51
なるる。 10000rpm/64bit PCI クラスですか。
うぅ、あちきのような素人には高価で手が出せませぬ。。。

# しかし想像すると恐いかも。。 > 箱から砂を出すような seek 音。。

これっていい解説サイトどこかにないかな？

# hdparm -Tt /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.21 seconds =105.79 MB/sec
Timing buffered disk reads: 64 MB in 3.40 seconds = 18.82 MB/sec

# hdparm -i /dev/hda

/dev/hda:

Model=WDC WD400BB-00AUA1, FwRev=18.20D18, SerialNo=WD-WMA6R3967169
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4 mode5

勝手気ままにチューニング
http://linux.ascii24.com/linux/allascii/linuxmag/articles/no_03/p213-217.pdf
(HTMLバージョン)

http://www.google.com/search?q=cache:oKd6CvQO_egC:linux.ascii24.com/linux/allascii/linuxmag/articles/no_03/p213-217.pdf+hdparm&hl=ja&lr=lang_ja

HDD の最適化
http://www.geocities.co.jp/SiliconValley-PaloAlto/5254/hddpfm.html

hdparm を使って IDE ディスクのパフォーマンスを引き出せ
http://libra.higashi.hit-u.ac.jp/manual/hdparm.html

>>54
サンクス！
今んとこ１割ほど性能向上中。
よーしパパ チューニングしちゃうぞー

-X がよく分からん。 何書きゃいいんだろ・・・

>>56
-X 2048

えーと、いろいろパラメータをいじったのですが
カーネルメイク時間で実測しても何も変化が見られなかったので
チューニングは中止です。

もともとDMAオンにしてたから それ以上は全然・・・

Maxtor 40MB 5400rpm 流体軸受、ほとんど無音。

# hdparm -Tt /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.94 seconds =136.17 MB/sec
Timing buffered disk reads: 64 MB in 1.84 seconds = 34.78 MB/sec
# hdparm -i /dev/hda

/dev/hda:

Model=Maxtor 4D040K2, FwRev=DAH017K0, SerialNo=D2H2884E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80043264
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

まあ、年代物のマシンだししょうがないかな。
このディスク、容量3GBしかないし、回転数5400もないかもしれんし。

#/sbin/hdparm -a128 -c1 -d1 -m16 -tT -f -i /dev/hda

/dev/hda:
setting fs readahead to 128
setting 32-bit I/O support flag to 1
setting multcount to 16
setting using_dma to 1 (on)
multcount = 16 (on)
I/O support = 1 (32-bit)
using_dma = 1 (on)
readahead = 128 (on)

Model=WDC AC33200L, FwRev=32.41N35, SerialNo=WD-WT3720272174
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=6296/16/63, TrkSize=57600, SectSize=600, ECCbytes=22
BuffType=DualPortCache, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=6296/16/63, CurSects=6346368, LBA=yes, LBAsects=6346368
IORDY=on/off, tPIO={min:160,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2

Timing buffer-cache reads: 128 MB in 3.25 seconds = 39.38 MB/sec
Timing buffered disk reads: 64 MB in 7.34 seconds = 8.72 MB/sec

# hdparm -tT /dev/hdc

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.61 seconds =209.84 MB/sec
Timing buffered disk reads: 64 MB in 1.71 seconds = 37.43 MB/sec

やっと、udma5が使えるようになりました。

気づかなかったけど、VIA VT82* South Bridge 使ってる場合、
RedHat7.2、付属のドライバ(via82cxxx.o)ではudma3/4/5が使えないみたい。
より新しいカーネルのドライバを使うと良いと思います。

(RedHat7.2のカーネルソース持ってる人は、
linux/drivers/ide/via82cxxx.c の436行目、
via_80w = 0;
っていうのをコメントアウトするとうまくいくかもしれません。
見たかんじ、これがケーブルの検出を無効にしてるみたいなので…
責任は持てませんが、私の場合はうまく動いるみたいです)

Vendor: SEAGATE Model: ST336737LW Rev: 0105

> hdparm -tT /dev/sda

/dev/sda:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28 MB/sec
Timing buffered disk reads: 64 MB in 4.47 seconds = 14.32 MB/sec
駄無なので速いのか遅いのか分かりません(w

最近このﾏｯｼｰﾝは全てSCSIにしてみたんだが
取りあえずIDEで組んでいた時よりは安定はしてる。

>>16

/dev/hda:

Model=ST380021A, FwRev=3.05, SerialNo=3HV07CBR
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.54 seconds =237.04 MB/sec
Timing buffered disk reads: 64 MB in 1.79 seconds = 35.75 MB/sec

ヤフーオークションで、凄い人気商品、発見！！！

「高性能ビデオスタビライザー」↓
http://user.auctions.yahoo.co.jp/jp/user/NEO_UURONNTYA

ヤフーオークション内では、現在、このオークション
の話題で、持ちきりです。

/dev/hda:

Model=IC25N020ATCS04-0, FwRev=CA2OA70A, SerialNo=隠してもしょうがないけど。
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=3(DualPortCache), BuffSize=1768kB, MaxMultSect=16, MultSect=16
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=39070080
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4 mode5

Timing buffer-cache reads: 128 MB in 1.10 seconds =116.36 MB/sec
Timing buffered disk reads: 64 MB in 3.24 seconds = 19.75 MB/sec

ATA33じゃあこんなもんか。
DJSA220に比べれば、むっちゃ静か。アクセス音は聞こえるけどね。

#cat scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: COMPAQ Model: BB01823469 Rev: 3B07
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_36_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03

/dev/sda:
Timing buffer-cache reads: 128 MB in 0.77 seconds =166.23 MB/sec
Timing buffered disk reads: 64 MB in 2.48 seconds = 25.81 MB/sec

/dev/sdc:
Timing buffer-cache reads: 128 MB in 0.77 seconds =166.23 MB/sec
Timing buffered disk reads: 64 MB in 1.84 seconds = 34.78 MB/sec

まあ、こんなもんか。

# cat scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST34371N Rev: 0484
Type: Direct-Access ANSI SCSI revision: 02
/dev/sda:
Timing buffer-cache reads: 128 MB in 11.21 seconds = 11.42 MB/sec
Timing buffered disk reads: 64 MB in 31.75 seconds = 2.02 MB/sec
……笑うしか無い

Timing buffer-cache reads: 128 MB in 1.23 seconds =104.07 MB/sec
Timing buffered disk reads: 64 MB in 4.61 seconds = 13.88 MB/sec
2年以上前の10GBハードディスク．

>>61
RH7.2付属のカーネルドライバソース書き換えですが、
この変更を行っても検出がうまくいくのでは無いようです、
無条件？で、Cable Type: 80wになりますので、やっぱり新しいのを
使ったほうがいいようです。

hdparm -itT /dev/hda

/dev/hda:

Model=ST340016A, FwRev=3.10, SerialNo=3HS1RGAP
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=-217054981, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.45 seconds =284.44 MB/sec
Timing buffered disk reads: 64 MB in 1.58 seconds = 40.51 MB/sec

Model=ST340810A, FwRev=3.31, SerialNo=5FB001KV
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.70 seconds =182.86 MB/sec
Timing buffered disk reads: 64 MB in 2.73 seconds = 23.44 MB/sec

こんな感じなんですけど、もっと速くなりますか？

hdparm -itT /dev/hda

/dev/hda:

Model=IBM-DJSA-220, FwRev=JS4OAC3A, SerialNo=44V44N87277
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=1874kB, MaxMultSect=16, MultSect=16
CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=39070080
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 2.71 seconds = 47.23 MB/sec
Timing buffered disk reads: 64 MB in 4.43 seconds = 14.45 MB/sec



おれのnote PC すげーおそいぞ。なんでだ？

>>70　U6ってヤツだよね？
サウスにあわせて、カーネルいじってみるとか…
汎用カーネルは遅いような気がするのはｵﾚだけか？

>>71　メーカは？って言うか、サウスは？
440MXでももう少し出ると思うんだが…

ってわけで、とりあえず>>54を参照すべし

>>72
> サウスにあわせて、カーネルいじってみるとか…

いじるってchipsetで選ぶだけですよね？
必要最低限のカーネルにしてるんですけどねぇ。

>>69-71
buffer-cacheの転送速度が全然違いますがな

メモリとプロセッサの差じゃないですかね

メモリも関係あるのかぁ。

FMV BIBLO NE9/1130
Pen3-1.13GHzなノート,i830MGチップセット

# hdparm -itT /dev/hda

/dev/hda:

Model=TOSHIBA MK4018GAP, FwRev=M0.03 A, SerialNo=12R64684T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=78140160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.65 seconds =196.92 MB/sec
Timing buffered disk reads: 64 MB in 2.95 seconds = 21.69 MB/sec

>>74　
ちなみに　AthronXP 1700+ +K7S5A(133/133) +DDR256x2 +BarraIV40G
う〜ん。読み込み自体はそこまで変わらないと思ってたYo!
けど、BarraIVとU6って、7200/5400rpmぐらいしか違わないような…

うーむ、U6 でも 23M でるのか。俺は BX なためか
11.25 しかでなかった。
# 2年以上昔の IBM のほうが 16.89 で速い。

PenIII + VT82c586B + マクの80G とか IBM DTLA とか色々で
どうやっても 16MB/s あたりで頭打ちになる。
over 20MB/s ってどんな環境で出るの?
ATA66 で使ってるけど、ATA100 だと出る?
5400rpm だとダメで 7200rpm だと出る?

CPU とかﾁﾌﾟｾﾄの情報もｷﾎﾞﾝ

/dev/hda:

Model=MAXTOR 4K080H4, FwRev=A08.1500, SerialNo=374118327334
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=156301487
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.78 seconds =164.10 MB/sec
Timing buffered disk reads: 64 MB in 4.17 seconds = 15.35 MB/sec

/dev/hdc:

Model=IBM-DTLA-305040, FwRev=TW4OA60A, SerialNo=YJEYJ0A8975
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.79 seconds =162.03 MB/sec
Timing buffered disk reads: 64 MB in 4.05 seconds = 15.80 MB/sec

[root@localhost root]# hdparm -itT /dev/hda

/dev/hda:

Model=IBM-DTLA-305030, FwRev=TW3OA60A, SerialNo=YG0YGT0A157
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60036480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 2.84 seconds = 22.54 MB/sec
あおぺんのブックベアボンですけどね。ぺんほーの。北森は載らないですが
1.7Gは割と普通に使用可能です。

/dev/hda:

Model=FUJITSU MPG3409AT E, FwRev=82B9, SerialNo=VH06T150CWSM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 2.32 seconds = 27.59 MB/sec

PIII(650)+vt82c686aだとこんな感じ
>>79
chipsetが本当に586Bだったらその辺が限界かもしれず
しかも、ATA66になってないよ

>>82
MPG3409AT-EF も持ってたけど、やっぱり 15MB/s 位だったな。
やっぱりサウスの責任かなぁ。
CPU は k6-III と Pen3-700 で hdparm -t の数値ぜんぜん
変わんなかったんだよね(サウスは一緒)。だから CPU は多分かんけいない。

hdparm -I で見ると /dev/hdc は udma4 に * が付くので ATA66
になってると思う。/dev/hda のほうはケーブルが ATA33 用なので
udma2 のままでいい。
実は ATA100 用ケーブル繋いだ /dev/hdc を udma4 で使ってみて
ぜんぜん改善しなかったので /dev/hda のほうを udma4 化する気力を
なくしてる ...

cat /proc/ide/hda/model
WDC WD800BB-53BSA0

hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.41 seconds =312.20 MB/sec
Timing buffered disk reads: 64 MB in 2.07 seconds = 30.92 MB/sec

はやいっすかね？満足してます。

/dev/hda:

Model=IC35L040AVVA07-0, FwRev=VA2OA52A, SerialNo=VNC202A2GXH4ZA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.74 seconds =172.97 MB/sec
Timing buffered disk reads: 64 MB in 1.46 seconds = 43.84 MB/sec

/dev/hde:

Model=ST340016A, FwRev=3.75, SerialNo=3HS460E5
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 1.64 seconds = 39.02 MB/sec

PCスペックは 青ペンのAX6BC TypeR +Cel900(OCで1008Mhz)+ 384MB
玄人指向ATA100-PCI さしてやってまふ。
こんなもんでしょうか?

/dev/hda:

Model=TOSHIBA MK6014MAP, FwRev=N2.10 A, SerialNo=207A4366T
Config={ Fixed }
RawCHS=12416/15/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=off
CurCHS=12416/15/63, CurSects=11733120, LBA=yes, LBAsects=11733120
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.59 seconds = 80.50 MB/sec
Timing buffered disk reads: 64 MB in 18.95 seconds = 3.38 MB/sec

3年前のNotePC。まだまだ鯖現役。

hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 5T030H3, FwRev=TAH71DP0, SerialNo=T3H00YAC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60030432
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.92 seconds =139.13 MB/sec
Timing buffered disk reads: 64 MB in 2.97 seconds = 21.55 MB/secB/sec

こんなもんか。

Model=ST340016A, FwRev=3.10, SerialNo=3HS12TNV
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.47 seconds =272.34 MB/sec
Timing buffered disk reads: 64 MB in 1.57 seconds = 40.76 MB/sec

K7S5A: SiS735 です。

昨日まで >>69, 86 さんみたいな速度がでなくて、やはり SiS か…
と鬱でしたが、原因はケーブルのほうでした。ごめんな > SiS

Model=ST340016A, FwRev=3.10, SerialNo=3HS1784E
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Kernel Drive Geometry LogicalCHS=77545/16/63 PhysicalCHS=77545/16/63
Timing buffer-cache reads: 128 MB in 1.93 seconds = 66.32 MB/sec
Timing buffered disk reads: 64 MB in 5.23 seconds = 12.24 MB/sec

Promise Ultra 100 TX2をKernel 2.2.20にパッチを当てて使ってます。
ATA-5で動いているのになぜか遅い。

Model=IC35L040AVER07-0, FwRev=ER4OA44A, SerialNo=SX0SX0V4252
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.64 seconds =200.00 MB/sec
Timing buffered disk reads: 64 MB in 1.93 seconds = 33.16 MB/sec
kernel2.4.18-686-smp VP_IDE: VIA vt82c686bです
オプションはhdparm -X68 -d1 -c1

Model=IC35L060AVVA07-0, FwRev=VA3OA52A, SerialNo=VNC302A3CBAR7A
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5

Timing buffer-cache reads: 128 MB in 0.53 seconds =241.51 MB/sec
Timing buffered disk reads: 64 MB in 1.42 seconds = 45.07 MB/sec
SuSE8.1 KT266Aです。

貴方の○○教えて下さい総合スレ立てた方がいいんちゃう。

Model=ST380021A, FwRev=3.75, SerialNo=3HV1BXB0
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.31 seconds =407.08 MB/sec
Timing buffered disk reads: 64 MB in 1.58 seconds = 40.50 MB/sec

Redhat7.3 P4S533(south SiS646)

チップセットのせいなんでしょうか？　U160　SCSIのカードに、15000回転の
HDDをつけても、PCI66MHzのスロットにプロミス社のU133DMAカードを挿して、
ATAの高速ディスクをいろいろ取り替えてみても、hdparm -t の値が、
どれも　40MB/s を越えません。どこにボトルネックがあるのでしょうか？

/dev/hda:
Model=IBM-DTTA-371010, FwRev=T77OA73A, SerialNo=WL0WLFA9614
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=465kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=19746720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2 udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 2.67 seconds = 47.94 MB/sec
Timing buffered disk reads: 64 MB in 6.41 seconds = 9.98 MB/sec

/dev/hdb:
Model=Maxtor 33073U4, FwRev=BAC51KJ0, SerialNo=N40AEPGC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=58633344
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 2.65 seconds = 48.30 MB/sec
Timing buffered disk reads: 64 MB in 6.83 seconds = 9.37 MB/sec

五年前のPCだからへろへろだ。

Sony NEWS 830(MC68020,16MHz)でCDC WREN-IV（SCSI-I）では、ddで
1.5MB/S 程度しかでなかったことが懐かしい。

みなさんは、woodyでどこのファイルにチューニングパラメータ書いてるんですか？

/dev/hda:
Model=Maxtor 90648D3, FwRev=GAS54812, SerialNo=A3HZ8DJC
Config={ Fixed }
RawCHS=12556/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=12556/16/63, CurSects=12656448, LBA=yes, LBAsects=12656448
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.08 seconds =118.52 MB/sec
Timing buffered disk reads: 64 MB in 4.65 seconds = 13.76 MB/sec

3年前のものだから、こんなもんか…
最近のは一発でもdisk readが50MB/sec越えるらしいでつね…

2 枚とも激遅いぞ。そんなに古くないのに。どうしてかしらん。

Model=WDC WD200EB-75CPF0, FwRev=06.04G06, SerialNo=WD-WMAAU2239225
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39102336
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.68 seconds =188.24 MB/sec
Timing buffered disk reads: 64 MB in 11.04 seconds = 5.80 MB/sec

Model=ST340810A, FwRev=3.99, SerialNo=3FB4AYJW
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.69 seconds =185.51 MB/sec
Timing buffered disk reads: 64 MB in 21.04 seconds = 3.04 MB/sec

5400rpmです。

/dev/hda:

Model=Maxtor 96147H8, FwRev=BAC51KJ0, SerialNo=N80JPCCC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=120060864
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 1.16 seconds =109.96 MB/sec
Timing buffered disk reads: 64 MB in 2.44 seconds = 26.28 MB/sec

>>100
おかしいね。PIOで動いてるような数字だ。
原因がわかったら教えてちょ。

nForce2使ったときのキャッシュの数字が見たいなあ

>>100
試しに
hdparm /dev/hda (で、dma の値を確認)
hdparm -d 1 /dev/hda
やってみ。

/sbin/hdparm -Tt /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.23 seconds =550.76 MB/sec
Timing buffered disk reads: read() failed: Success

ガーン、I/Oエラーが出てる。

# /sbin/hdparm -itT /dev/hda

/dev/hda:

Model=IC35L080AVVA07-0, FwRev=VA4OA50K, SerialNo=VNC400A4G6WT3A
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5

Timing buffer-cache reads: 128 MB in 0.57 seconds =224.56 MB/sec
Timing buffered disk reads: 64 MB in 1.41 seconds = 45.39 MB/sec

さっきやったら180Mと40M位だった。
あれって思ったらHなmpg見てた。(w

# hdparm -i /dev/hda

/dev/hda:

Model=ST340016A, FwRev=3.19, SerialNo=3HS9K9PJ
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

# hdparm -t /dev/hda

/dev/hda:
Timing buffered disk reads: 64 MB in 1.67 seconds = 38.32 MB/sec

体感速度は440BX+U6の18MB/sと全く変わらず。
サーバー交換しても速度アップのメリットゼロ。
むしろ熱さと重低音の響きに悩む。
もう5400回転近所で売ってないのが口惜しい。

我が家のホーム鯖
[root@server /root]# hdparm -itT /dev/hda

/dev/hda:

Model=SAMSUNG SV1204H, FwRev=RK100-10, SerialNo=0450J1FT802738
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234493056
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : fastATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 1.22 seconds =104.92 MB/sec
Timing buffered disk reads: 64 MB in 1.71 seconds = 37.43 MB/sec

>>108
ハード板に、年末は店頭のHDDの玉数が減る、と書いてあった。
また来年になれば出回るんじゃん。

>>104
指摘どうもありがとうございました。たしかにDMA off でした。しかし、
on にしようとするとできない (not permitted) と言われました。

返事遅くなって済みません。出張中だったんで。

>>111
そういうときは、慌てず騒がずsuでrootになって
もう一度
/sbin/hdparm -d 1 /dev/hda しる

>>112
ははは。そりゃ、いくら俺でも root でやっとるよ。ついでに umount してやって
みたがそれでもダメ。root じゃなければ Permission denied ってでるわな。

>>113
おれも Intel 845GE, Intel ICH4 なマザボで DMA on に出来なかった。
kernel に -ac patch あてたら DMA on になったよ。

>>114
サンクス。言われて思いついて調べてみた。俺の場合 KT333
なんだけど 2.4.19-pre5 以上でないと dma つかえないらしい。
原因わかったんでそのうち kernel を新しくするわ。

>>107
それは、-Tの数値を理解していないと思われ。
manにもわりと詳しくかいてある。読め。

ヲレも2.4.19のときDMA onに出来なかったのでパッチあてたよ
2.4.20でカーネル作り直したら，そのままでDMA使用できた．

ケーブルがふるいタイプのものだと、実力が出せなかったりするし、
なぜかしらないがVine2.5だと、/etc のしたにあるコンフィグレーション
ファイルでDMAをオンにしないと、デフォルトではPIOでHDDがつながっている。

>>118
どのファイルですか? fstab? 俺もしかしたらそれに当っているかも知れない。

>>119
/etc/sysconfig/harddisks

>>120 サンクス。たしかに comment out されてるね。しらんかった。安全の為らしいが。

ここはpureIDE限定デスカー？
昔，Escaladeで計ったら-tで80Mぐらい出たような…

>>105
pupu.
strerror()がSUCCESS（藁

>>114-117
そういうのは大概，パッチ無くともDeviceID書き加えるだけでOKと成り候。

>>122
チップセットが新しい場合でも？
ちなみに自分の場合は845Gだったんだけど
パッチ当てる，もしくは2.4.20でカーネルをつくり直さないと
DMAをONに出来なかった．
時間があればDeviceIDをどのように書き加えればいいのか
ポインタだけでもいいから教えて.

VIA の VT82* チップの載ったマザーを使っているんだけど、
どうしても udma3/4/5 が有効にならないんです。

2.4.20 に ac パッチ当てて使ってみてるんですが。
それとも何かカーネルの設定で必要な項目とかあるのですかね。

ポインタでも良いのでどなたかお助け〜。

>>124
/proc/ide/via きぼん

こんなかんじです。

----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.35-ac
South Bridge: VIA vt82c686a
Revision: ISA 0x1b IDE 0x6
Highest DMA rate: UDMA66
BM-DMA base: 0xd000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: no no
Post Write Buffer: no no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: DMA PIO DMA PIO
Address Setup: 30ns 120ns 30ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 90ns 90ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 90ns 270ns
Cycle Time: 120ns 600ns 180ns 600ns
Transfer Rate: 16.6MB/s 3.3MB/s 11.1MB/s 3.3MB/s

ちなみに hdparm -i はこんな具合です。

/dev/hda:

Model=DupliDisk IDE RAID-1 Adapter( 1.27), FwRev=VA2OA50K, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-

DupliDisk IDE RAID-1 Adapter の先にATA100対応のディスクが付いてます。
DupliDisk って製品は ATA66 対応を謳ってるRAIDコントローラです。

今気づいたんですが、Cable Type が 40w として認識されて
しまってるのが原因っぽいですね。Dupli Diskに付属のケーブル
を使っているのですが、マニュアルに通常のATAケーブルじゃ駄目だ
と書いていたので素直に従ってるんですけどね。

一応、製品仕様には 80wire - 40pin Connector とあります。

もしかすると、カーネルの問題かもしれず。

/usr/src/linux/drivers/ide/via82cxxx.c

の中で、無条件に via_80w に 0 を入れている場面があれば、犯人はカーネルです。
変なパッチが当てられてると思うので、そのパッチを抜いて再構築ですな。

# ちなみに、Vine-2.5 の　kernel-2.4.18-0vl3 はその問題を抱えてました。

>>123
最高に手抜きな方法。
まったくの新設計チップだとちと困るが，同系統のチップが以前にある場合…
2.4系カーネルなら
linux/include/pci_ids.h
にある同系統チップのDeviceIDを自前のものに書き換える。

845GのICH4ならICH3のDeviceIDを置き換えてしまうといいだろう。

>>130
どうも
でも、厨なんでいまいちよく分からない、もうちょっと教えとくれ
dmesg見たら
---------------------------
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
.......
i810: Intel ICH4 found at IO 0xe400 and 0xe000, IRQ 11
.......

のように書かれていたので
pci_ids.hの
#define ....INTEL_82801BA_[0-9] hoge
のところの hogeの値を 0xe400 0xe000とかに替えて
カーネル作りなおしたらいいの?

のぉ、厨にわかるよう説明するの下調べが面倒臭い。。。

自分のIDEコントローラの調べ方：
* PCI_IDE: unknown IDE controller on PCI bus xx device xx, VID=xxxx, DID=xxxx

対応してない(unknown)なコントローラなら、VID=xxxx DID=xxxx として
Vendor、Deviceの各IDが表示される。

置換元のDeviceの調べ方:
linux/drivers/pci/pci.ids
や
http://pciids.sf.net/
を見て、旧世代のIDEコントローラのIDを探す。

* (VID)8086 (DIV)244b (Desc.)82801BA IDE U100

今回はこのICH2 UDMA100コントローラを生贄にしてみようか。

実際に置換する：
linux/include/linux/pci_ids.h内で、先の置換元を探すと

#define PCI_DEVICE_ID_INTEL_82801BA_9 0x244b

とある。これを書き換え。
#define PCI_DEVICE_ID_INTEL_82801BA_9 0xXXXX
(DID:244b->XXXX)
とすれば良い。

>>133
どうもありがと
少し賢くなったよ.
123=117だよ

あ、122だった。
番号一つ間違えター。
逝っときます。

/dev/hda:

Model=Maxtor 4D080K4, FwRev=DAH017K0, SerialNo=D4H07X8E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.36 seconds =355.56 MB/sec
Timing buffered disk reads: 64 MB in 1.88 seconds = 34.04 MB/sec

結果が変なので困ってる。なんでだろ。UDMA66なのに遅過ぎる。変なメッセージは出るし。

# hdparm -i /dev/hda

/dev/hda:

Model=WDC WD205BA, FwRev=16.13M16, SerialNo=WD-WM9490076499
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40088160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled

# hdparm -Tt /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 4.33 seconds = 29.56 MB/sec
Timing buffered disk reads: 64 MB in 3.65 seconds = 17.53 MB/sec
Hmm.. suspicious results: probably not enough free memory for a proper test.

IP記録実験
http://qb.2ch.net/test/read.cgi/accuse/1042013605/

1 名前：ひろゆき ◆3SHRUNYAXA ＠どうやら管理人 ★ 投稿日：03/01/08 17:13 ID:???
そんなわけで、qbサーバでIPの記録実験をはじめましたー。

27 名前：心得をよく読みましょう 投稿日：03/01/08 17:20 ID:yL/kYdMc
SETTING.TXT管轄でないということは全鯖導入を視野に、か？

38 名前：ひろゆき ◆3SHRUNYAXA 投稿日：03/01/08 17:22 ID:rLfxQ17l
>>27
鋭いです。

73 名前：ひろゆき ◆3SHRUNYAXA 投稿日：03/01/08 17:27 ID:rLfxQ17l
＞ところで、IPが抜かれて何か今までと変わることってあるのでしょうか？
・今までより、サーバが重くなる。
・裁判所や警察からの照会があった場合にはIPを提出することがある。

ひろゆきって男前だよな

>>440
そんなに寄付集まらないと思うぞ。
利用者に月１万円って現実的ですか？

Σもろふしあなさん！？>>535

匿名とは、自分が提示する情報だけで勝負することをいうので、

Timing buffer-cache reads: 128 MB in 0.48 seconds =266.67 MB/sec
Timing buffered disk reads: 64 MB in 1.59 seconds = 40.25 MB/sec

遅いと思ってたけど、ここ見るとそうでもないみたいだな。
UT2003とかでテクスチャレベルを最高にするとテクスチャ読み込むのが遅すぎてサーバ側から切断される。
これはメモリが足りないせいなのかな。256しか積んでないからな。

cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03

hdparm -tT /dev/sda
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.17 seconds =752.94 MB/sec
Timing buffered disk reads: 64 MB in 1.27 seconds = 50.39 MB/sec

安定しないため、あえてスピード落としてる人っていますか？

ウチだと
80芯ケーブル
hda: WDC WD400AB-00BVA0(40ギガ)
hdb: ST340810A(40ギガ)
40芯ケーブル
hdc: cdrom
で、1日1回完全フリーズ、たまに突然再起動。

80芯ケーブル
hda: ダミーの850Mボロディスク
hdb: ST340810A
40芯ケーブル
hdc: cdrom
hdd: WDC WD400AB-00BVA0
で、安定です。

hdaのWDC WD400AB-00BVA0をumda2くらいに落としてやれば安定するような気がす
るのですが。

電源の最悪値はとりあえず置いておいて下さい。

（＾＾）

/dev/hda:

Model=FUJITSU MPG3409AT E, FwRev=82C4, SerialNo=VH06T170K5AM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.60 seconds = 80.00 MB/sec
Timing buffered disk reads: 64 MB in 2.49 seconds = 25.70 MB/sec

/dev/hdb:

Model=FUJITSU MPF3204AT, FwRev=0028, SerialNo=05086825
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40031712
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 1 2 3 4 5

Timing buffer-cache reads: 128 MB in 0.32 seconds =400.00 MB/sec
Timing buffered disk reads: 64 MB in 2.78 seconds = 23.02 MB/sec

2.4.20 + Con Kolivas patch for 2.4.20 + ReiserFS
これからhdparmで性能をアップしていくぞ

>>148
バッファキャッシュの値が小さすぎるような…
hdpram実行時にsuspicious云々なメッセージ出ませんでした？

マシン：EPIA-C800 MEM:256M
OS：DEBIAN 3.0

/dev/hdb:

Model=MAXTOR 4K080H4, FwRev=A08.1500, SerialNo=674117721182
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301487
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=disabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.96 seconds = 65.31 MB/sec
Timing buffered disk reads: 64 MB in 8.93 seconds = 7.17 MB/sec

＋＋＋＋＋＋＋＋＋＋＋＋＋＋＋

EDENって６６MがMAXでしたっけ・・・？１００まで使えたような気がしたんですが。
まぁ用途が家鯖なので全然問題ないんですが（笑

もう１台

マシン：DURON750+K7SEM
OS：赤帽８．０

/dev/hda:

Model=Maxtor 2F040L0, FwRev=VAM51JJ0, SerialNo=F12B8AKE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80293248
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 1.03 seconds =123.89 MB/sec
Timing buffered disk reads: 64 MB in 2.17 seconds = 29.49 MB/sec

上のマシンのもう１台のHDD

/dev/hdb:

Model=IC35L060AVER07-0, FwRev=ER6OA44A, SerialNo=SZ0SZ062567
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5

Timing buffer-cache reads: 128 MB in 1.04 seconds =122.73 MB/sec
Timing buffered disk reads: 64 MB in 2.64 seconds = 24.27 MB/sec

$ hddparm -tT
bash: hddparm: command not found

[root@localhost root]# /sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 98196H8, FwRev=ZAH814Y0, SerialNo=V80SXMXC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160045200
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 0.72 seconds =178.58 MB/sec
Timing buffered disk reads: 64 MB in 2.28 seconds = 28.03 MB/sec

>>150
でませんでしたよ〜。

もう一度やってみますた。
Timing buffer-cache reads: 128 MB in 1.63 seconds = 78.53 MB/sec
Timing buffered disk reads: 64 MB in 2.25 seconds = 28.44 MB/sec

nForce2マザー(K7N2G-L)買ったんでやってみました。

VineSeed標準のkernel-2.4.20-0vl14だと

/dev/hda:
Timing buffered disk reads: 64 MB in 18.20 seconds = 3.52 MB/sec

という悲惨な状態だったのでいろいろ調べた結果、カーネルにACパッチの
patch-2.4.21-pre4-ac4.bz2をあてて、カーネルパラメータに
ide0=ata66を指定することで

/dev/hda:
Timing buffered disk reads: 64 MB in 1.80 seconds = 35.56 MB/sec

まで出ました。感動。

VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
hda: ST38410A, ATA DISK drive
hda: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=16708/16/63, UDMA(33)

# hdparm -i /dev/hda
/dev/hda:
Model=ST38410A, FwRev=3.03, SerialNo=6CS1JE84
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=512kB, MaxMultSect=32, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=16841664
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

# hdparm -m16 -c1 -u1 -d1 -tT /dev/hda
/dev/hda:
setting 32-bit I/O support flag to 1
setting multcount to 16
setting unmaskirq to 1 (on)
setting using_dma to 1 (on)
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
Timing buffer-cache reads: 128 MB in 3.13 seconds = 40.89 MB/sec
Timing buffered disk reads: 64 MB in 5.31 seconds = 12.05 MB/sec

# hdparm -itT /dev/hda

/dev/hda:

Model=TOSHIBA MK3004GAH, FwRev=JB001A, SerialNo=13830056T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=58595040
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.20 seconds =106.67 MB/sec
Timing buffered disk reads: 64 MB in 4.17 seconds = 15.35 MB/sec

/dev/hda:
Model=Maxtor 6Y080L0, FwRev=YAR41VW0, SerialNo=Y3HXS84E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ataATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6 ATA-7

Timing buffer-cache reads: 128 MB in 0.34 seconds =376.47 MB/sec
Timing buffered disk reads: 64 MB in 1.33 seconds = 48.12 MB/sec

/dev/hda:

Model=Maxtor 5T060H6, FwRev=TAH71DP0, SerialNo=
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117187500
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 1.78 seconds = 35.96 MB/sec

（＾＾）

ぉぉ？

/dev/hda:

Model=FUJITSU MPG3409AT E, FwRev=82C4, SerialNo=VH06T170K5AM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.09 seconds =117.43 MB/sec
Timing buffered disk reads: 64 MB in 18.53 seconds = 3.45 MB/sec

>163
ｶﾞｯ

>164
MPG3049ATE 。。。ｶﾞｸｶﾞｸﾌﾞﾙﾌﾞﾙ｡｡｡

━―━―━―━―━―━―━―━―━[JR山崎駅（＾＾）]━―━―━―━―━―━―━―━―━―

/dev/hda:

Model=ST3160023A, FwRev=3.06, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 1.07 seconds =119.63 MB/sec
Timing buffered disk reads: 64 MB in 1.17 seconds = 54.70 MB/sec

>>123
やったけどならなかったよ？

/dev/hda:

Model=IC35L080AVVA07-0, FwRev=VA4OA52A, SerialNo=VNC402A4GGNWAA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.87 seconds =147.13 MB/sec
Timing buffered disk reads: 64 MB in 1.42 seconds = 45.07 MB/sec

Abit NF7-SのSATA(SilliconImage3112A)接続

Model=WDC WD360GD-00FNA0
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.17 seconds = 54.70 MB/sec

Model=Maxtor 6Y060L0 (SERILLEL2利用)
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.34 seconds = 47.76 MB/sec

hdg: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
ってのがコンソールにワンサカでてくるな。
siimage.cで#if 1で括ってあるprintk()を取っ払ってしまえば良さげではあるが．．

=== [ ▼PR ] =========================================================
獲得ページにて毎日ポイント獲得！広告すると毎日のポイント増えるかも！？
http://wwa.irias.co.jp/?WCI=Home&WCE=242081
======================================================== [ ▲PR ] ====

Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y2VTRHCE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.13 seconds =984.62 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.64 MB/sec

# hdparm -tT /dev/hda

/dev/hda:
read() failed: Input/output error
Timing buffered disk reads: read() failed: Input/output error

・・・(´Д｀；)

# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.22 seconds =581.82 MB/sec
止まってしまった、、

% ps auxww|grep hdparm
root 31075 0.0 0.1 2352 1468 pts/1 D 18:26 0:00 /sbin/hdparm -tT /dev/hda
どうすればいいんだ??

Dで止まったら、お手上げさぁね。

>>177-178
kill してもダメ?

/dev/hda:

Model=FUJITSU M2724TA, FwRev=7604, SerialNo=06115464
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=3162/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=3162/16/63, CurSects=3187296, LBA=yes, LBAsects=3187836
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3

Timing buffer-cache reads: 128 MB in 2.62 seconds = 48.85 MB/sec
Timing buffered disk reads: 64 MB in 18.30 seconds = 3.50 MB/sec

遅い(ﾟДﾟ)ｺﾞﾙｧ

/dev/hde:

Model=HDS722512VLSA80, FwRev=V33OA60A, SerialNo=VNRC3EC3C415DK
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=241254720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 1632 MB in 2.00 seconds = 814.90 MB/sec
Timing buffered disk reads: 96 MB in 3.01 seconds = 31.91 MB/sec

1年半前のノートだからあまり速くない
/dev/hda:

Model=TOSHIBA MK4018GAP, FwRev=M0.03 A, SerialNo=12R64684T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78140160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 648 MB in 2.01 seconds = 322.60 MB/sec
Timing buffered disk reads: 64 MB in 3.07 seconds = 20.87 MB/sec

/dev/hda:

Model=ST340016A, FwRev=3.05, SerialNo=3HS0CVGL
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 1020 MB in 2.00 seconds = 510.00 MB/sec
Timing buffered disk reads: 124 MB in 3.04 seconds = 40.79 MB/sec

/dev/hdb:

Model=ST380011A, FwRev=3.04, SerialNo=3JV00Q8V
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 1004 MB in 2.00 seconds = 502.00 MB/sec
Timing buffered disk reads: 168 MB in 3.01 seconds = 55.81 MB/sec

＿|￣|○
そこまで速いというわけでもなかったのね…

Model=IC35L080AVVA07-0, FwRev=VA4OA52A, SerialNo=VNC402A4CP9LRA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

* signifies the current active mode

Timing buffer-cache reads: 1520 MB in 2.00 seconds = 760.00 MB/sec
Timing buffered disk reads: 138 MB in 3.04 seconds = 45.39 MB/sec
なぜか udma3 udma4 udma5 が出ないけど，UDMA(100)とdmesgには出てる
kernel 2.4.22で，dmesgには
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=10011/255/63, UDMA(100)
とあるんだけども。

Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE1006441
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:
Timing buffer-cache reads: 2104 MB in 2.00 seconds = 1052.00 MB/sec
Timing buffered disk reads: 178 MB in 3.01 seconds = 59.14 MB/sec

Model=ST3120026AS, FwRev=3.05, SerialNo=3JT0LQ15
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:
Timing buffer-cache reads: 2116 MB in 2.00 seconds = 1058.00 MB/sec
Timing buffered disk reads: 74 MB in 3.00 seconds = 24.67 MB/sec


Seagageだめぽ

# /sbin/hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.06 seconds =120.75 MB/sec
Timing buffered disk reads: 64 MB in 2.11 seconds = 30.33 MB/sec
# cat /proc/ide/hda/model
ACCUSYS ACS7500 1.2

Model=Maxtor 6Y120L0, FwRev=YAR41BW0, SerialNo=Y3JAZLLE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=240121728
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):

* signifies the current active mode

Timing buffer-cache reads: 3152 MB in 2.00 seconds = 1576.00 MB/sec
Timing buffered disk reads: 158 MB in 3.01 seconds = 52.49 MB/sec

/dev/hdb:

Model=IBM-DTLA-307020, FwRev=TX3OA50C, SerialNo=YHDYHT6F813
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

Timing buffer-cache reads: 2892 MB in 2.00 seconds = 1446.00 MB/sec
Timing buffered disk reads: 106 MB in 3.03 seconds = 34.98 MB/sec

/dev/sda:
Timing buffer-cache reads: 656 MB in 2.01 seconds = 326.58 MB/sec
Timing buffered disk reads: 48 MB in 3.02 seconds = 15.90 MB/sec
USB接続のディスク
本体にUSB1.1用ポートもあるが、恐くて試す気にはならない

/dev/hda:

Model=ST3120026A, FwRev=3.16, SerialNo=3JT0HTQN
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234375000
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

/dev/hda:
Timing buffer-cache reads: 2368 MB in 2.00 seconds = 1184.18 MB/sec
Timing buffered disk reads: 168 MB in 3.02 seconds = 55.58 MB/sec

アゲ

$ /sbin/hdparm -tT /dev/hda
/dev/hda: Permission denied

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.44 seconds = 88.89 MB/sec
Timing buffered disk reads: 64 MB in 15.61 seconds = 4.10 MB/sec
$ cat /proc/ide/hda/model
Maxtor 6Y200P0
みんな速いなぁ

USB1.1接続にして測定してみたぞ
/dev/sdc:
Timing buffer-cache reads: 700 MB in 2.01 seconds = 348.83 MB/sec
Timing buffered disk reads: 4 MB in 4.24 seconds = 966.64 kB/sec

はじめはうかつにも曲聞きながら(USB Audio,48kHz 16bit)チャレンジしたら
I/O Error となってしまった。曲を止めて気をとりなおしてチャレンジ

$ cat /proc/ide/hda/model
FUJITSU MHT2040AT SP

$ cat /proc/ide/hdc/model
UJDA750 DVD/CDRW

/dev/hda:
Timing buffer-cache reads: 752 MB in 2.00 seconds = 375.12 MB/sec
Timing buffered disk reads: 82 MB in 3.00 seconds = 27.30 MB/sec

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.38 seconds =336.84 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.64 MB/sec

# cat /proc/ide/hda/model
Maxtor 6Y080L0
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.46 seconds =278.26 MB/sec
Timing buffered disk reads: 64 MB in 1.14 seconds = 56.14 MB/sec

# cat /proc/ide/hda/model
ST3120026A
/dev/hda:
Timing buffer-cache reads: 1648 MB in 2.00 seconds = 823.18 MB/sec
Timing buffered disk reads: 140 MB in 3.04 seconds = 46.04 MB/sec

# cat /proc/ide/hda/model
Maxtor 6Y080L0

/dev/hda:
Timing buffer-cache reads: 1124 MB in 2.00 seconds = 562.00 MB/sec
Timing buffered disk reads: 172 MB in 3.01 seconds = 57.14 MB/sec

FUJITSU MPB3032ATU,ATA DISK Drive

/dev/hda:
Timing buffer-cache reads: 128 MB in 10.14 seconds = 12.62 MB/sec
Timing buffered disk reads: 64 MB in 22.72 seconds = 2.82 MB/sec

cat /proc/ide/hda/model
Maxtor 6Y060L0

/dev/hda
Timing buffer-cache reads: 1732 MB in 2.00 seconds = 866.00 MB/sec
Timing buffered disk reads: 146 MB in 3.04 seconds = 48.11 MB/sec

遅いのか早いのかよくわかりません

/dev/hda:

Model=HDS722516VLAT80, FwRev=V34OA60A, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 424 MB in 2.01 seconds = 211.40 MB/sec
Timing buffered disk reads: 136 MB in 3.02 seconds = 45.10 MB/sec

/dev/hdc:

Model=ST3160023A, FwRev=3.06, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 440 MB in 2.00 seconds = 219.59 MB/sec
Timing buffered disk reads: 106 MB in 3.04 seconds = 34.90 MB/sec

hda と hdcでだいぶ違うのをハケーン。
DMA on なんだけど。

/dev/hda:

Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y288LDDE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156250000
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.37 seconds =346.00 MB/sec
Timing buffered disk reads: 64 MB in 5.86 seconds = 10.92 MB/sec

/dev/hdc:

Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y2875BJE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156250000
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.36 seconds =354.62 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.45 MB/sec

# cat /proc/ide/hda/model
HITACHI_DK23FB-40

# hdparm -tT
Timing buffer-cache reads : 128MB in 0.84 seconds =152.38 MB/sec
Timing buffered disk reads: 64MB in 13.25 seconds = 4.83 MB/sec

Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE1006441
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 1924 MB in 2.00 seconds = 961.18 MB/sec
Timing buffered disk reads: 204 MB in 3.02 seconds = 67.60 MB/sec

>>210
漏れもﾗﾌﾟﾀｿ2使ってるけどその位の速度。
速くて快適だ…

# hdparm -tiT /dev/hde

/dev/hde:

Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE10603XX
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 2072 MB in 2.00 seconds = 1035.12 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.18 MB/sec

HITACHI_DK23DA_16N

Timing buffer-cache reads: 128MB in 1.44 seconds = 88.89 MB/sex
Timing buffered disk reads: 64MB in 4.59 seconds = 13.94 MB/sec

FUJITSU MAS3367NP

Timing buffer-cache reads: 4044MB in 2.00 seconds = 2021.30 MB/sex
Timing buffered disk reads: 226MB in 3.01 seconds = 75.04 MB/sec

>>212
>>213
Timing buffer-cacheの行の単位がMB/sexになってるぞ!!

'hddparm' は、内部コマンドまたは外部コマンド、
操作可能なプログラムまたはバッチ ファイルとして認識されていません。

# cat /proc/ide/hda/model
IBM-DTTA-350840

# /sbin/hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.98 seconds =130.61 MB/sec
Timing buffered disk reads: 64 MB in 6.21 seconds = 10.31 MB/sec

遅いなぁ・・・P3-500じゃこんなものか

Timing buffer-cache reads: 3420 MB in 2.00 seconds = 1709.41 MB/sec
Timing buffered disk reads: 192 MB in 3.00 seconds = 63.92 MB/sec

速いのかな?

>>217
チップセット何？

>218
ICH5 S-ATAなHDD

$ cat /proc/ide/hda/model
ST340810A
$ /sbin/h
halt hwclock
$ sudo apt-get install hdparm
[...]
Setting up hdparm (4.5-1.2) ...

$ sudo /sbin/hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.96 seconds = 65.31 MB/sec
Timing buffered disk reads: 64 MB in 9.50 seconds = 6.74 MB/sec

]# hdparm -tiT /dev/hda

/dev/hda:

Model=HTS726060M9AT00, FwRev=MH4OA68A, SerialNo=MRH401M4G5JHZB
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 1984 MB in 2.00 seconds = 993.14 MB/sec
Timing buffered disk reads: 110 MB in 3.03 seconds = 36.31 MB/sec

iオプション付けた方が見栄えするな

CPUをP3-500からCeleron 500に変えたんでもう一度晒し。
# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=IBM-DTTA-350840, FwRev=T55OA73A, SerialNo=WE0WEH11545
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=467kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=16514064
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.64 seconds = 78.05 MB/sec
Timing buffered disk reads: 64 MB in 6.75 seconds = 9.48 MB/sec

FSBの差は大きいな。

Virtual マシンに入れた Fedora Core 1

$ sudo /sbin/hdparm -tiT /dev/hda
Password:

/dev/hda:

Model=Virtual HD, FwRev=1. 1, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=512, ECCbytes=0
BuffType=DualPortCache, BuffSize=64kB, MaxMultSect=128, MultSect=128
CurCHS=33288/16/63, CurSects=33554304, LBA=yes, LBAsects=33554304
IORDY=on/off, tPIO={min:333,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no

* signifies the current active mode

Timing buffer-cache reads: 496 MB in 1.99 seconds = 249.25 MB/sec
Timing buffered disk reads: 44 MB in 3.06 seconds = 14.38 MB/sec

i840+P3-500MHzマシン

# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Maxtor 90680D4, FwRev=PAS23B15, SerialNo=V417RWVA
Config={ Fixed }
RawCHS=13176/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=13176/16/63, CurSects=13281408, LBA=yes, LBAsects=13281408
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 5.18 seconds = 12.36 MB/sec

玄人志向のATA133RAID-PCI2につないだHDS722516VLAT80(非RAID)

/dev/sda:
Timing buffer-cache reads: 128 MB in 1.27 seconds =100.79 MB/sec
Timing buffered disk reads: 64 MB in 1.92 seconds = 33.33 MB/sec

カードのBIOSではUDMA5だけどATA33で飽和してるっぽい。
scsi認識だから-iで情報見られないし、-d1は効かないしなぁ。

IC35L180AVV207-1
Timing buffer-cache reads: 1092 MB in 2.00 seconds = 544.72 MB/sec
Timing buffered disk reads: 156 MB in 3.05 seconds = 51.09 MB/sec

Maxtor 6Y200P0
Timing buffer-cache reads: 1048 MB in 2.00 seconds = 524.08 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.62 MB/sec

まぁこんなもんか。

>>213 の MAS とか >>217 の Raptor(?) とかはやっぱり桁違いに速い
ですね。

今年発表された各社の威信を賭けたハイエンドSCSI新モデル群は
何処まで逝くか楽しみですな。

/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST313620A, FwRev=3.07, SerialNo=7BW11BTT
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=26692776
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 2.56 seconds = 25.00 MB/sec

pentium2 450x2 + 初代BarracudaATA 13.6GB

DellPowerEdge400SC+FedoraCore1+linux-2.4.26

/dev/hdb:

Model=ST3200822A, FwRev=3.01, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 2472 MB in 2.00 seconds = 1236.00 MB/sec
Timing buffered disk reads: 186 MB in 3.00 seconds = 62.00 MB/sec

同じノートをまだ使っているが
半年ほど前にHDDを換えてみた(40G→80G)
回転数も上がったから多少は速くなっているかも
/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL422L4GK498B
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 664 MB in 2.00 seconds = 331.55 MB/sec
Timing buffered disk reads: 110 MB in 3.05 seconds = 36.04 MB/sec

i815 + PenIII-S1.4GHz + linux-2.6.9-gentoo-r6
静かで涼しい、俺の大好きなHDD　現在25°C
/dev/hda:

Model=ST340015A, FwRev=3.01, SerialNo=5LA7VAT5
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing cached reads: 624 MB in 2.01 seconds = 311.11 MB/sec
Timing buffered disk reads: 130 MB in 3.02 seconds = 43.02 MB/sec

薔薇5400っすか

/dev/hda:

Model=IBM-DJNA-351520, FwRev=J56OA30K, SerialNo=G80GLWHN168
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=430kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=30033360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 17: 1 2 3 4

Timing buffer-cache reads: 128 MB in 1.34 seconds = 95.52 MB/sec
Timing buffered disk reads: 64 MB in 4.42 seconds = 14.48 MB/sec

/dev/hda:

Model=HDS728040PLAT20, FwRev=PF1OA21B, SerialNo=PFD112S1RWBWUD
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
BuffType=DualPortCache, BuffSize=1719kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: Reserved:

* signifies the current active mode

Timing cached reads: 1328 MB in 2.00 seconds = 663.44 MB/sec
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.87 MB/sec

model: HDS722512VLAT80
/dev/hda:
Timing buffer-cache reads: 628 MB in 2.00 seconds = 314.00 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.62 MB/sec

model: Maxtor 6Y120P0
/dev/hdb:
Timing buffer-cache reads: 620 MB in 2.00 seconds = 310.00 MB/sec
Timing buffered disk reads: 144 MB in 3.03 seconds = 47.52 MB/sec

model: Maxtor 6Y120P0
/dev/hdd:
Timing buffer-cache reads: 620 MB in 2.00 seconds = 310.00 MB/sec
Timing buffered disk reads: 146 MB in 3.01 seconds = 48.50 MB/sec

３台とも静穏モードだけど、hdaの日立（IBM）は設計が新しいだけあって速いみたいだな。
ソフトウェアraidドライバとかnfsとかsambaとか動かしたまま

# cat /proc/ide/hda/model;hdparm -tT /dev/hda
IBM-DTLA-307045

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 2.57 seconds = 24.90 MB/sec


# cat /proc/ide/hdc/model;hdparm -tT /dev/hdc
WDC WD400BB-75FRA0

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 2.73 seconds = 23.44 MB/sec

# cat /proc/ide/hda/model;hdparm -tT /dev/hda
Maxtor 6Y120L0

/dev/hda:
Timing cached reads: 1904 MB in 2.00 seconds = 950.72 MB/sec
Timing buffered disk reads: 146 MB in 3.04 seconds = 48.07 MB/sec

/dev/hda:

Model=ST380011A, FwRev=8.01, SerialNo=5JVEGW6M
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156295279
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing cached reads: 2536 MB in 2.00 seconds = 1267.56 MB/sec
Timing buffered disk reads: 166 MB in 3.01 seconds = 55.10 MB/sec

＃　このスレみて自分のドライブが異様に遅いのに気付くまで、
＃　ケーブルが古い４０芯でUDMA-33で動作してるのに気付かなかった
＃
＃　ちなみに同じドライブでこれぐらいだった↓
＃　Timing cached reads: = 250 MB/sec
＃ Timing buffered disk reads: = 28 MB/sec

/dev/hda:

Model=ST36422A, FwRev=1.70, SerialNo=7AC01TSV
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=13228/15/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=13228/15/63, CurSects=12500460, LBA=yes, LBAsects=12500460
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version: 1 2 3 4

* signifies the current active mode

/dev/hda:
Timing cached reads: 532 MB in 2.00 seconds = 266.00 MB/sec
Timing buffered disk reads: 42 MB in 3.03 seconds = 13.86 MB/sec

カタカタうるさいディスク、

僕のｼﾝｺﾊﾟｯﾄﾞでつ。

# hdparm -tT /dev/hda1

/dev/hda1:
Timing cached reads: 620 MB in 2.01 seconds = 308.20 MB/sec
Timing buffered disk reads: 70 MB in 3.04 seconds = 23.01 MB/sec

HDDを買い換えて2ﾏｿしたっす。2ﾏｿ払った成果はあるようです。

/dev/hdd:

Model=QUANTUM FIREBALL EX6.4A, FwRev=A0A.0D00, SerialNo=276903422458
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=13325/15/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=418kB, MaxMultSect=16, MultSect=16
CurCHS=13325/15/63, CurSects=12592125, LBA=yes, LBAsects=12592847
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 15: 1 2 3 4

* signifies the current active mode

Timing cached reads: 2432 MB in 2.00 seconds = 1214.36 MB/sec
Timing buffered disk reads: 38 MB in 3.03 seconds = 12.54 MB/sec

5年ぐらい前のHDだが、まあ歳相応の性能ってところか。

# hdparm -iTt /dev/hde [~]

/dev/hde:

Model=WDC WD740GD-00FLA1, FwRev=27.08D27, SerialNo=WD-WMAKE1601147
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing cached reads: 2096 MB in 2.00 seconds = 1047.11 MB/sec
Timing buffered disk reads: 204 MB in 3.03 seconds = 67.38 MB/sec

なんで cached read がやたら遅いんだろう。

# hdparm -tiT /dev/hda

/dev/hda:

Model=QUANTUM FIREBALL ST3.2A, FwRev=A0F.F800, SerialNo=153718315215
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=6256/16/63, TrkSize=32256, SectSize=512, ECCbytes=4
BuffType=DualPortCache, BuffSize=81kB, MaxMultSect=16, MultSect=16
CurCHS=6256/16/63, CurSects=6306048, LBA=yes, LBAsects=6306048
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no
Drive conforms to: device does not report version: 1 2 3

* signifies the current active mode

Timing cached reads: 116 MB in 2.04 seconds = 56.86 MB/sec
Timing buffered disk reads: 28 MB in 3.15 seconds = 8.89 MB/sec


とっても遅いづら。

RAID組んで測っているのは無いんか？

# hdparm -itT /dev/hda

/dev/hda:

Model=TOSHIBA MK2103MAV, FwRev=D0.05 A, SerialNo=97874156
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=4200/16/63, TrkSize=40257, SectSize=639, ECCbytes=21
BuffType=DualPortCache, BuffSize=128kB, MaxMultSect=16, MultSect=16
CurCHS=4200/16/63, CurSects=4233600, LBA=yes, LBAsects=4233600
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3

Timing buffer-cache reads: 128 MB in 5.84 seconds = 21.92 MB/sec
Timing buffered disk reads: 64 MB in 27.53 seconds = 2.32 MB/sec


10年前のPentium120MHzノート+東芝2G+Vine2.5で使ってる自宅鯖。(*´▽`*) ｵｿｰｲ

hdparm -tT /dev/sda10

/dev/sda10:
Timing buffer-cache reads: 128 MB in 0.13 seconds =984.62 MB/sec
Timing buffered disk reads: 64 MB in 0.78 seconds = 82.05 MB/sec

Vendor: DELL Model: Virtual Disk 0 Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02

hdparm -tiT /dev/hda

/dev/hda:

Model=IC35L120AVVA07-0, FwRev=VA6OA52A, SerialNo=VNC603A6GGEZVA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=241254720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

* signifies the current active mode

Timing cached reads: 1704 MB in 2.00 seconds = 851.28 MB/sec
Timing buffered disk reads: 126 MB in 3.04 seconds = 41.41 MB/sec

hdparm -tiT /dev/hda

/dev/hda:

Model=IBM-DYLA-28100, FwRev=YSAAA23H, SerialNo=VC0VC033424
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=15880/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=459kB, MaxMultSect=16, MultSect=off
CurCHS=15880/16/63, CurSects=16007040, LBA=yes, LBAsects=16007040
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: mode=0x80 (128)
Drive conforms to: ATA-3 X3T10 2008D revision 1: 1 2 3

* signifies the current active mode

Timing cached reads: 232 MB in 2.01 seconds = 115.27 MB/sec
Timing buffered disk reads: 22 MB in 3.04 seconds = 7.24 MB/sec

/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Maxtor 91728D8, FwRev=GAS54112, SerialNo=A80BELHC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=33750864
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 17: 1 2 3 4

* signifies the current active mode

Timing cached reads: 240 MB in 2.00 seconds = 120.00 MB/sec
Timing buffered disk reads: 46 MB in 3.11 seconds = 14.79 MB/sec

/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL442L4GNDMDB
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 1384 MB in 2.01 seconds = 690.04 MB/sec
Timing buffered disk reads: 104 MB in 3.00 seconds = 34.61 MB/sec

dev/hdb:
Timing cached reads: 816 MB in 2.00 seconds = 407.86 MB/sec
Timing buffered disk reads: 162 MB in 3.05 seconds = 53.19 MB/sec

$ sudo /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Virtual HD, FwRev=1. 1, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=512, ECCbytes=0
BuffType=DualPortCache, BuffSize=64kB, MaxMultSect=128, MultSect=128
CurCHS=33288/16/63, CurSects=33554304, LBA=yes, LBAsects=33554304
IORDY=on/off, tPIO={min:333,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no

* signifies the current active mode

Timing buffer-cache reads: 1636 MB in 1.99 seconds = 822.11 MB/sec
Timing buffered disk reads: 92 MB in 3.01 seconds = 30.56 MB/sec

Debian:~# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ASI ARAID99 1000 Ver1.00, FwRev=v1.00.47, SerialNo=A020-0272-14001-0000
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:0,rec:0}
PIO modes: pio3 pio4
DMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.94 seconds =136.17 MB/sec
Timing buffered disk reads: 64 MB in 14.16 seconds = 4.52 MB/sec
Debian:~#

俺のは遅すぎたみたい。
家でﾊﾟﾗﾒﾀさわってみた


Debian:~# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ASI ARAID99 1000 Ver1.00, FwRev=v1.00.47, SerialNo=A020-0272-14001-0000
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=8
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:0,rec:0}
PIO modes: pio3 pio4
DMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.90 seconds =142.22 MB/sec
Timing buffered disk reads: 64 MB in 1.15 seconds = 55.65 MB/sec
Debian:~#

漏れもそう思っていたが書かなかった(w

Model=ST340015A, FwRev=3.01, SerialNo=5LAJT6PR
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

Timing cached reads: 112 MB in 2.01 seconds = 55.76 MB/sec
Timing buffered disk reads: 30 MB in 3.12 seconds = 9.63 MB/sec

なんでこんなに遅いんだろ・・・？
ファーヤーボールでも19MB/secまで出てたのに・・

$ sudo hdparm -tiT /dev/hda

/dev/hda:

Model=ST340810A, FwRev=3.39, SerialNo=5FB2VY20
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 2.07 seconds = 61.84 MB/sec
Timing buffered disk reads: 64 MB in 2.46 seconds = 26.02 MB/sec

このスレ見てDMAがOFFになってたのに気づいた。。。
何年気づかずに使ってたんだろう。。。orz

# /sbin/hdparm -itT /dev/hda

/dev/hda:

Model=ST340014A, FwRev=3.06, SerialNo=5JX6TNFS
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing cached reads: 2088 MB in 2.00 seconds = 1044.16 MB/sec
Timing buffered disk reads: 166 MB in 3.03 seconds = 54.79 MB/sec

Model=HDS722525VLAT80, FwRev=V36OA63A, SerialNo=VN693ECFE0YJWD
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 3596 MB in 2.00 seconds = 1797.37 MB/sec
Timing buffered disk reads: 176 MB in 3.01 seconds = 58.38 MB/sec

Model=WDC WD135BA, FwRev=16.13M16, SerialNo=WD-WMA02
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=16
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=26406576
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4

# hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 32 MB in 1.45 seconds =22.10 MB/sec

# hdparm -itT /dev/hde

/dev/hde:

Model=IC35L060AVV207-0, FwRev=V22OA63A, SerialNo=VNVB01G2G5H4YE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1821kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 384 MB in 2.02 seconds = 190.13 MB/sec
Timing buffered disk reads: 72 MB in 3.05 seconds = 23.60 MB/sec

# hdparm -itT /dev/hdf

/dev/hdf:

Model=HDS722516VLAT20, FwRev=V34OA6EA, SerialNo=VNR41EC4CR3P4M
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1794kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 320 MB in 2.02 seconds = 158.36 MB/sec
Timing buffered disk reads: 92 MB in 3.01 seconds = 30.55 MB/sec

一つの外付けのケースに入れたドライブ（Toshiba MK8026GAX）を、

1). IEEE1394 で接続した場合

/dev/sda:
Timing cached reads: 528 MB in 2.01 seconds = 262.69 MB/sec
Timing buffered disk reads: 58 MB in 3.12 seconds = 18.59 MB/sec

と、

2). USB2.0 で接続した場合

/dev/sda:
Timing cached reads: 556 MB in 2.00 seconds = 278.00 MB/sec
Timing buffered disk reads: 36 MB in 3.05 seconds = 11.80 MB/sec

とで計測。

物理的にはまったく同じケース＋ドライブだけど、
接続方法が違うだけでこんなに違う。

ちなみに IEEE1394 は VIA OHCI Compliant IEEE 1394 Host Controller、
USB2 は NEC PCI to USB Enhanced Host Controller B1 の、
それぞれ PCI バスに刺したカード経由。

2台でSoftware Raid0を組んでみた。

# hdparm -tT /dev/md0

/dev/md0:
Timing cached reads: 3560 MB in 2.00 seconds = 1778.49 MB/sec
Timing buffered disk reads: 412 MB in 3.01 seconds = 136.81 MB/sec

$ sudo hdparm -tiT /dev/hda

/dev/hda:

Model=FUJITSU MHT2080AH, FwRev=006C, SerialNo=NP0FT5428V6T
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 2648 MB in 2.00 seconds = 1322.88 MB/sec
Timing buffered disk reads: 102 MB in 3.02 seconds = 33.75 MB/sec


dell inspiron 700m でカキコ
ていうか今ごろ気づいたけど F かよ。。
まぁもれは以前のHDDぶっこわれ事件のときに壊れる前に
ソフマップに売り抜けた勝ち組だからべつにいいけどwww

/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL455L4JBARTB
Timing cached reads: 1660 MB in 2.00 seconds = 829.95 MB/sec
Timing buffered disk reads: 104 MB in 3.05 seconds = 34.12 MB/sec

/dev/hdc:

Model=PIONEER DVD-RW DVR-K15, FwRev=1.11, SerialNo=
Timing cached reads: 1640 MB in 2.00 seconds = 819.95 MB/sec
Timing buffered disk reads: 10 MB in 3.29 seconds = 3.04 MB/sec

/dev/hda:

Model=HDT722516DLAT80, FwRev=V43OA70A, SerialNo=VD071BTCCT8RSE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
BuffType=DualPortCache, BuffSize=7674kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: Reserved:

* signifies the current active mode

Timing cached reads: 2232 MB in 2.00 seconds = 1115.05 MB/sec
Timing buffered disk reads: 164 MB in 3.01 seconds = 54.57 MB/sec

cat /proc/ide/hda/model
ST380021A

hdparm -tT /dev/hda
Timing cached reads: 1744 MB in 2.00 seconds = 871.95 MB/sec
Timing buffered disk reads: 110 MB in 3.01 seconds = 36.57 MB/sec

cat /proc/ide/hda/model
ST380021A

/sbin/hdparm -tT /dev/hda
Timing cached reads: 1288 MB in 2.00 seconds = 644.00 MB/sec
Timing buffered disk reads: 114 MB in 3.04 seconds = 37.50 MB/sec

cat /sys/block/sdb/device/model
9500S-4LP DISK

hdparm -tT /dev/sdb
/dev/sdb:
Timing cached reads: 2768 MB in 2.00 seconds = 1382.83 MB/sec
Timing buffered disk reads: 250 MB in 3.01 seconds = 82.99 MB/sec

sage

/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=HDS722516VLAT20, FwRev=V34OA60A, SerialNo=VNR4GEC4C5G9XK
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1794kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 552 MB in 2.00 seconds = 276.00 MB/sec
Timing buffered disk reads: 174 MB in 3.00 seconds = 58.00 MB/sec

cat /proc/ide/hda/model
ST3120022A
hdparm -tT /dev/hda
/dev/hda:
Timing cached reads: 4024 MB in 2.00 seconds = 2011.33 MB/sec
Timing buffered disk reads: 156 MB in 3.02 seconds = 51.73 MB/sec

cat /sys/block/sda/device/model
WDC WD740GD-75FL
hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 4064 MB in 2.00 seconds = 2030.88 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.18 MB/sec

/dev/hda: HDS728080PLAT20（ATA-66）
multcount = 0 (off)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 16383/255/63, sectors = 160836480, start = 0

Timing cached reads: 2596 MB in 2.00 seconds = 1298.20 MB/sec
Timing buffered disk reads: 150 MB in 3.01 seconds = 49.91 MB/sec

>>234 もうあったのか

setting multcount to 16
setting xfermode to 70 (UltraDMA mode6)
に変更して

Timing cached reads: 2536 MB in 2.00 seconds = 1267.56 MB/sec
Timing buffered disk reads: 150 MB in 3.03 seconds = 49.53 MB/sec

変わらず･･･マルチセクタOff、UDMA4で十分らしい

dmesgにCRCエラーが出るんでどないなっとんじゃいと思ったら
ケーブル腐ってました･･･

/dev/hda:
Timing cached reads: 2552 MB in 2.00 seconds = 1275.56 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.61 MB/sec

ここはHDDの歴史がわかるスレですね

/sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 4R060L0, FwRev=RAMC1TU0, S/sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 4R060L0, FwRev=RAMC1TU0, SerialNo=R2R9P42E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):

* signifies the current active mode

Timing cached reads: 1132 MB in 2.01 seconds = 564.39 MB/sec
Timing buffered disk reads: 112 MB in 3.01 seconds = 37.21 MB/sec

ﾃﾗｼｮﾎﾞｽ orz

なんだかしらんが、こんな数字がでたぞ。

# hdparm -tT /dev/sda

/dev/sda:
Timing cached reads: 4180 MB in 1.99 seconds = 2098.48 MB/sec
Timing buffered disk reads: 142 MB in 3.03 seconds = 46.92 MB/sec

# hdparm -tT /dev/hda

/dev/hda:
Timing cached reads: 1760 MB in 2.00 seconds = 878.93 MB/sec
Timing buffered disk reads: 62 MB in 3.04 seconds = 20.42 MB/sec

# cat /proc/ide/hda/model
HTC426060G9AT00

恐怖のX40ユーザーですが、お前らこんにちは。
1.8インチHDDは速度こそこの通りunkoburiburiですが、びっくりするほど衝撃に強いですよ。

/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST313620A, FwRev=3.07, SerialNo=7BW11BTT
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=26692776
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.55 seconds =232.73 MB/sec
Timing buffered disk reads: 64 MB in 2.92 seconds = 21.92 MB/sec

P2-450x2とPC100 SDRAMから、P3-800(133）x2とPC800-45に変更した
結構メモリ速度あがるね

cat /sys/block/sda/device/model
WDC WD1600JS-00N
hdparm -tT /dev/sda

/dev/sda:
Timing cached reads: 3128 MB in 2.00 seconds = 1563.46 MB/sec
Timing buffered disk reads: 174 MB in 3.01 seconds = 57.84 MB/sec

linuxhost ~ # cat /sys/block/sda/device/model
Hitachi HDT72503
linuxhost ~ # hdparm -Tt /dev/sda
/dev/sda:
Timing cached reads: 1632 MB in 2.00 seconds = 815.94 MB/sec
Timing buffered disk reads: 220 MB in 3.00 seconds = 73.30 MB/sec

linuxhost ~ # cat /sys/block/sdb/device/model
WDC WD740GD-00FL
linuxhost ~ # hdparm -Tt /dev/sdb
/dev/sdb:
Timing cached reads: 1624 MB in 2.00 seconds = 811.51 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.14 MB/sec

ST3250620AS
/dev/sda:
Timing cached reads: 3004 MB in 2.00 seconds = 1501.91 MB/sec
Timing buffered disk reads: 230 MB in 3.00 seconds = 76.56 MB/sec

ST3200822A
/dev/hda:
Timing cached reads: 2996 MB in 2.00 seconds = 1497.91 MB/sec
Timing buffered disk reads: 186 MB in 3.01 seconds = 61.83 MB/sec

Vendor: FUJITSU Model: MAW3300NC Rev: 5803
/dev/sda:
Timing cached reads: 3624 MB in 2.00 seconds = 1811.37 MB/sec
Timing buffered disk reads: 276 MB in 3.02 seconds = 91.31 MB/sec

$ cat /sys/block/sda/device/model
WDC WD740ADFD-00

$ sudo /sbin/hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 4028 MB in 2.00 seconds = 2015.55 MB/sec
Timing buffered disk reads: 250 MB in 3.02 seconds = 82.88 MB/sec

SEAGATE Model: ST336754LC Rev: D404
でした

>>286
うわっ、速。

# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST320014A, FwRev=3.07, SerialNo=5JZB6NW7
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39102336
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.61 seconds =209.84 MB/sec
Timing buffered disk reads: 64 MB in 2.15 seconds = 29.77 MB/sec